-
VIX BITS
-
-
Pre-drill PERFECT pilot holes for hinges to receive the #12 wood screw in commercial doors. Did you know, in most cases, the door manufacturers' warranty is VOIDED if pilot holes for hinge screws are not drilled prior to installing hinges ?
-
#1, #2 & #3 INSERT TIPS W/STAINLESS STEEL MAGNETIC HOLDERS
-
-
GOTTA have the RIGHT tips for the JOB !! GET (10) ONE INCH #1 PHILLIPS INSERT TIPS , (10) ONE INCH #2TIPS AND (20) ONE INCH #3TIPS WITH (3) MAGNETIC STAINLESS STEEL HOLDERS TOO !! These are the REAL DEAL.. Hugs the screw head NICE n TIGHT !! YES.. THE HOLDERS ARE STAINLESS STEEL AND MAGNETIC
-
#1, #2 & #3 PHILLIPS TIPS (2" AND 3" SETS)
-
-
GOTTA have the RIGHT tips for the JOB !! GET (10) ONE INCH #1 PHILLIPS INSERT TIPS , (10) ONE INCH #2TIPS AND (20) ONE INCH #3TIPS WITH (3) MAGNETIC STAINLESS STEEL HOLDERS TOO !! These are the REAL DEAL.. Hugs the screw head NICE n TIGHT !! YES.. THE HOLDERS ARE STAINLESS STEEL AND MAGNETIC
-
#12 Vix Bit Replacement H.S.Drill Bits (QTY: 2)
-
-
This is the replacement drill bit for the #12 Vix Bit by S.E Vick Tool Company. YOU ARE GETTING TWO (2) of them !!
-
#12 Vix Bit Replacement Spring
-
-
This is the replacement spring for the #12 Vix Bit by S.E Vick Tool Company.
-
3/8" Paddle Bits QTY=6 for $10
-
-
3/8 " Paddle Bit for Installing MOST door closers on wood doors.
-
50/50 Ready Shim COMBO
-
-
SAVE A FEW BUCKS !! HERE'S A SPECIAL COMBO OF 100 READY SHIMS FOR RATED AND NON-FIRE RATED DOORS. They're an E-Z FIX FOR SAGGING DOORS OR DOORS THAT FIT TOO TIGHT IN THE FRAME . YOU GET 50 PEEL AND STICK SHIMS FOR NON RATED DOORS AND 50 PEEL AND...
-
BANG-IT "The Ultimate Hinge Pin Remover !"
-
-
QUICK, EASY and SAFE WAY TO to remove A DOOR ! NO DRILLS REQUIRED !
-
CLICK'S KWIK DRILL
-
-
Drill Pilot holes for commercial hinges on wood doors in NOTHING FLAT ! Drill ALL 4 hinge holes at one time in one motion USING YOUR CORDLESS OR POWER DRILL. Talk about FAST !!! it's like having 4 Vix-Bits going at the same time.
-
CLOSER ARM SUPPORT PLATE
-
-
Ever tried to Attach a Closer Arm to a thin Metal Frame that has NO Reinforcement inside ? The Closer arm cannot attach securely and will pull away from the frame. When there is NO re-inforcement INSIDE the FRAME , support has to come from the...
-
COMMERCIAL JIG KIT FOR 4-1/2" HINGES & ANSI STRIKE
-
-
BE PREPARED !!! FIELD PREP WOOD DOORS AND FRAMES for 4-1/2" HINGES AND 4-7/8 X 1-1/2 ANSI STRIKE. JUST use YOUR CLAMPS ! NO NAILS REQUIRED ! NO NAIL HOLES to FILL !! ROUTER BIT AND CORNER CHISEL INCLUDED !! ALL JIGZ , BITS AND CORNER CHISELS ARE MADE IN THE USA !!
-
COMMERCIAL JIG KIT FOR HINGES & LATCHES
-
-
BE PREPARED !!! FIELD PREP WOOD DOORS AND FRAMES for HINGES AND LATCHES JUST use YOUR CLAMPS ! NO NAILS REQUIRED ! NO NAIL HOLES to FILL !! CHOOSE any TWO HINGES …... 5.0" , 4-1/2", 4.0, 4.0 with 5/8 Radius, 3 1/2 and 3 1/2 with 5/8 Radius. LATCH...
-
CUTTERS FOR DBB MORTISER
-
CARBIDE TIPPED WOOD CUTTERS AND ALUMINUM CUTTERS FOR DBB MORTICER
-
CYLINDER WRENCH
-
-
USE THIS COOL TOOL TO INSTALL UN-CORED T CYLINDERS IN NO TIME AT ALL. THEY'RE SIMPLE TOOLS AND VERY EASY TO USE. A REAL TIME SAVER . AVAILABLE FOR SCHLAGE AND BEST CYLINDERS
-
DBB MORTICER by Souber Tools
-
-
You wouldn’t believe how many calls and emails we get from guys wanting a tool to mortise doors or drill a raceway that won’t break their pocketbook. Well...we have FOUND that Bad Boy !!! The DBB Morticer by Souber Tools. What a Tool !! One tool...
-
DBB MORTICER LONG SHAFT
-
-
LONG SHAFT for locks 185mm in depth… about 7-1/2" deep to 7-7/8" depending on the size cutter used.
-
DBB MORTICER STANDARD SHAFT
-
-
STANDARD REGULAR SHAFT for DBB MORTICER
-
DOOR MAINTENANCE AND REPAIR KIT (Fire Doors and NonRated Doors)
-
-
Sometimes you don't know what you need until you need it... That’s why we’ve got it !!! You NEVER know what you’re gonna run into when it comes to door and hardware maintenance and repairs. Might see Broken off or Stripped out screws that need to...
-
DOOR PRESSURE GAUGE
-
-
Take the Guesswork out of adjusting door pressure to meet ADA Specs . Use the Door Pressure gauge. For 0-35 lb Force Range. Very easy to operate.
-
DRILLERZ-N-TAPPERZ KIT
-
-
Tried of RUINING Drill BITS when Attaching CLOSER ARMS or CONTINUOUS HINGES to Metal Frames Filled with Grout ? Here's a Specialty KIT to save you TIME and MONEY. Like having 100 Disposable Drill Bits and Taps !!
-
HINGE JIGZ COMBO PAK W/ROUTER BIT & CORNER CHISEL!!
-
-
Be Prepared. !!!......IT'S NOW EASY TO FIELD MORTISE Wood DOORS or Wood Frames FOR HINGES......NO NAILS ! JUST CLAMP IT !!! HINGE JIGZ Combo PAK includes (1) Universal Fence and these 6 Hinge JIGZ >>>5.0", 4-1/2 " 4.0" & 4.0" with 5/8 radius for...
-
HINGE MORTISING SYSTEM (4TOPS & THE RAILS !) DOORS & FRAMES !!
-
-
JUSTDOORTOOLZ HINGE MORTISING SYSTEM FOR 3 OR 4 HINGES . NO NAILS REQUIRED . NO NAIL HOLES TO FILL ! JUST CLAMP IT !! EASY TO ASSEMBLE AND LAYOUT. TAKE A LOOK AT THE PICS ! EACH HINGE SIZE sold Separately !! IT'S JUST 2SIMPLE !! ROUTER BIT & CORNER CHISEL INCLUDED !! USA MADE AND AWESOME !!
-
HINGE, STRIKE & LATCH REPAIR KIT
-
-
For WALLOWED or STRIPPED OUT LATCHES on HOLLOW METAL DOORS. Simply Place CLIPZ in position on LATCH then Install Lock. Clipz gives the screw Something to hold on to. They work PERFECT !! Use PLUGZ to FILL holes that have been WALLOWED out or NOT...
-
JAMM…THE DOOR WEDGE (2 for $30)
-
-
Need a secure way to hold a swinging door in one place while you MORTISE it or INSTALL HARDWARE on it ? Here is IT IS !! JAMM is the DOOR WEDGE YOU PLACE UNDER THE DOOR EDGE !! It works on ALL FLOOR surfaces . AWESOME Door Wedge for the Door and...
-
JUST DOOR CLIPZ ( QTY = 24)
-
-
For WALLOWED or STRIPPED OUT LATCHES on HOLLOW METAL DOORS. Simply Place Clipz in position on LATCH then Install Lock. Clipz gives the screw Something to hold on to. They work PERFECT !! SIZE: Small Clipz for Cylindrical Locks(CZ-1) and Large for...
-
JUST DOOR JIG For FLUSHBOLTS ( 1 " wide)
-
-
Field Mortise Wood Doors for AUTOMATIC FLUSHBOLTS. Made for 1-3/4" thick Doors. JUST use YOUR CLAMPS ! NO NAILS REQUIRED ! NO NAIL HOLES to FILL !! Works with your Plunge Router using a 1/2" bit with 5/8" collar.
-
JUST DOOR JIG For GLYNN JOHNSON CONCEALED OVERHEAD HOLDER
-
-
Field Mortise Wood Doors for GLYNN Johnson 100 SERIES or 410 Concealed OverHead Holder and mortise for the bracket in wood frames too ! Made for 1-3/4" thick Doors. JUST use YOUR CLAMPS ! NO NAILS REQUIRED ! NO NAIL HOLES to FILL !! Works with...
-
JUST DOOR JIG For ROCKWOOD 3-7/8" EDGE PULL
-
Made for Rockwood 880 Cast Edge Pull or similar. Works with your Plunge Router using a 1/2" bit with 5/8" collar. JUST use YOUR CLAMPS ! NO NAILS REQUIRED ! NO NAIL HOLES to FILL !! 1/2" router bit is Included !! HANDMADE IN THE USA !!!
-
JUST DOOR JIG For SOLIS MORTISE LOCK W/TRIM
-
BitS Included !! HandMade... USA !!!
-
JUST DOOR JIGZ ..TOPS ONLY!!!
-
-
FIELD MORTISE DOORS FOR HINGES, LATCHES AND STRIKES ...NO NAILS !!! JUST use YOUR CLAMPS ! NO NAILS REQUIRED ! NO NAIL HOLES to FILL !! BUY SETS and SAVE
-
JUST DOOR JIGZ Commercial Combo SAVE $$$$
-
-
COMMERCIAL HINGE, LATCH & STRIKE JIGZ COMBO !! FIELD MORTISE DOORS ...NO NAILS !!! JUST use YOUR CLAMPS ! NO NAILS REQUIRED ! NO NAIL HOLES to FILL !! ROUTER BIT AND CORNER CHISEL , BORING BITS AND STURDY CARRYING BAG INCLUDED !!! JIGS ARE MADE IN USA !
-
JUST DOOR JIGZ For CONCEALED HINGES
-
-
CONCEALED HINGE JIGZ.... WORKS ON DOORS AND FRAMES. Works with your Plunge Router using a 1/2" bit with 5/8" collar. JUST use YOUR CLAMPS ! NO NAILS REQUIRED ! NO NAIL HOLES to FILL !! Bit IS Included !! AVAILABLE ...SOSS #218...SOSS...
-
JUST DOOR JIGZ for HINGES (ROUTER BIT INCLUDED !!)
-
-
FIELD MORTISE DOORS FOR HINGES...NO NAILS !!! JUST use YOUR CLAMPS ! NO NAILS REQUIRED ! NO NAIL HOLES to FILL !! SETS INCLUDE: TOP, FENCE & ROUTER BIT !!!
-
JUST DOOR JIGZ FOR LATCHES & FACEPLATES (ROUTER BIT INCLUDED !!)
-
-
FIELD PREP DOORS FOR LATCHES ...NO NAILS !!! JUST use YOUR CLAMPS ! NO NAILS REQUIRED ! NO NAIL HOLES to FILL !! ROUTER BIT INCLUDED !!! MADE IN USA !! QUICK AND EASY !!!
-
JUST DOOR JIGZ FOR STRIKES
-
-
FIELD MORTISE DOORS FOR STRIKES ...NO NAILS !!! JUST use YOUR CLAMPS ! NO NAILS REQUIRED ! NO NAIL HOLES to FILL !! SETS INCLUDE: TOP, FENCE & ROUTER BIT !!!
-
JUST DOOR PLUGZ (50 PACK)
-
-
Re-Set Mis-Aligned Hinges and Protruding Screws or Holes that have been Wallowed OUT in WOOD DOORS or FRAMES !!! You no longer need to roam around the jobsite looking for a 2x4 to shave off slivers of wood to fill bad hinge or latch holes so you...
-
LATCH MARKING TOOL
-
-
This Latch Marking Tool does just THAT !!! After Whacking it with a hammer...it Marks an outline for you to HAND CHISEL the notch for the latch . 3 sizes available: 1" x 2-1/4"...1-1/8" x 2-1/4" ...or ...1-1/8" x 2-3/4" If you have a ROUTER and...
-
LCN SPRAY PAINT
-
-
Perfect MATCH for LCN and Finishes that LOOKS like LCN.
-
LEVER DRILL TOOL SCHLAGE & FALCON
-
-
FOR MORE ACCURATE AND SIMPLE DRILLING OF THROUGH BOLT HOLES IN PREDRILLED DOORS. SCHLAGE AL & ND LOCKS, FALCON, YALE AND MARKS
-
LOCK BORING JIG KIT (2-3/4" BACKSET FOR 1-3/4" THICK DOORS)
-
-
Here's a KIT for FIELD MORTISING Perfect Lock Bores and Latches on Wood Doors for CYLINDRICAL LOCKS. JIGZ are MADE to FIT ....Just SLide it onto Door and USE your CLAMPS to CLAMP IT !! Then Use the 2-1/8" Bit to Bore Holes from BOTH...
-
LOCK BORING JIG KIT (2-3/8" BACKSET)
-
-
Here's a KIT for FIELD MORTISING Perfect Lock Bores and Latches on Wood Doors for CYLINDRICAL LOCKS. JIGZ are MADE to FIT ....Just SLide it onto Door and USE your CLAMPS to CLAMP IT !! Then Use the 2-1/8" Bit to Bore Holes from BOTH...
-
LONG DRILL ADAPTER with 4 foot BIT FOR DBB MORTICER
-
This attachment , along with the DBB MORTISER, allows you the ability to DRILL RACEWAYS THRU DOORS FOR ELECTRICAL WIRING.
-
LONG DRILL BITS FOR DBB MORTISER
-
This BIT WITH THE Long Drill Adapter attachment used with the DBB MORTISER, allows you the ability to DRILL RACEWAYS THRU DOORS up to 4 feet wide FOR ELECTRICAL WIRING.
-
MORTISE CYLINDER TAP & DIE SET
-
-
MORTISE LOCK CASE HAS STRIPPED OUT CYLINDER THREADS ??? When mortise cylinders and lock cases are new they screw together without a problem. Often times a mortise cylinder is forced out of a lock without loosening the retaining screw. Other times...
-
MORTISE CYLINDER TAP ONLY
-
-
MORTISE LOCK CASE HAS STRIPPED OUT CYLINDER THREADS ??? When mortise cylinders and lock cases are new they screw together without a problem. Often times a mortise cylinder is forced out of a lock without loosening the retaining screw. Other times...
-
NEW !! LEO POCKET FLASHLIGHT by NEBO
-
-
The LEO™ is an amazingly versatile pocket light. Fully dimmable and equipped with Memory Power Setting, the LEO’s work light and spot light pivot and rotate to direct the light wherever you need it. A pocket clip, magnetic base and a kick stand /...
-
NORSEMAN SCREW/BOLT EXTRACTOR (10 PIECE SET)
-
-
USA MADE ......Left Hand Spiral Drill Screw and Bolt Extraction Set Door & Hardware Installers, Locksmiths and Facilities Maintenance guys need THIS bolt extractor set! Made in the USA by Norseman CTD (Viking), this 10 Piece Bolt Extractor Left...
-
OFF-SET HOUSING ADAPTER FOR DBB MORTICER
-
This attachment , along with the DBB MORTISER, allows you the ability to mortise hinges and strikes in doors and some frames.
-
READY TO HANG: FIELD GUIDE
-
-
READY TO HANG is a Field Guide for Basic Organization and Installation of Commercial Doors and Hardware. If you're somewhere in the loop of getting commercial doors and hardware INSTALLED then this Guide is for YOU. No FluFF !
-
READY- SHIMS for FIRE-RATED Doors
-
-
Did you know that THE NATIONAL FIRE PROTECTION AGENCY sets standards for the installation and maintenance of Fire-Rated Door Assemblies. According to NFPA 80, section 6.4.3.4, steel shims are the ONLY acceptable shim to be used when shimming...
-
READY- SHIMS for FIRE-RATED Doors WITH DOOR GAP GAUGE
-
-
Did you know that THE NATIONAL FIRE PROTECTION AGENCY sets standards for the installation and maintenance of Fire-Rated Door Assemblies. According to NFPA 80, section 6.4.3.4, steel shims are the ONLY acceptable shim to be used when shimming...
-
Replacement Bits for Kwik Drill (Qty=4)
-
-
Set of (4) Replacement Drill Bits for your Kwik Drill
-
REPLACEMENT CLIP FOR TEMPORARY DOOR LOCK
-
-
Replacement In-Swing clip for Temporary Door Lock. ..Just incase you misplaced the other one.
-
SMALL BORE KIT (1/2") for DBB MORTICER
-
-
Doors need a Small 1/2" MORTICE ?? Just Add this Small Bore Kit to your DBB Morticer !! There you have IT.. You're READY to Get the Job Done !! THIS IS AN ATTACHMENT FOR THE DBB MORTICER. Includes Small Housing Kit, Shaft and Depth Stop, 13mm (~1/2" ) Wood Cutter and 14.6 mm (~37/64" )wood cutters.
-
SPECIAL HOUSING ADAPTER FOR EXTRA THICK DOORS ( DBB MORTICER)
-
This attachment , along with the DBB MORTISER, allows you the ability to mortise Doors and FRAMES that are THICKER than 2-1/8" ! FOR Doors up to 3-3/4" THICK !!
-
Stainless Steel DRILLING KIT.....INCLUDES 9 BITS !!
-
-
Drilling thru Stainless Steel wiLL GIVE you FITS ... ... unless... you have the RIGHT BITS...... !!! Our Stainless STeeL Drilling KIT will HELP YOU get the job done. Kit Includes Everything you need to drill up to 1/4" diameter hole thru...
-
TEMPORARY DOOR LOCK ( In-Swing/ Out-Swing)
-
-
This Temporary Construction Lock Eliminates the need for costly locks. It will NOT damage to your doors or door-frames. Simply attach to a metal door frame with a minimum two-inch face, close your 1¾ inch door, apply a padlock and walk away. All...
-
TEMPORARY DOOR LOCKS ( Exit ONLY)
-
-
THE EXIT ONLY TEMPORARY DOOR LOCK works on 1¾ inch doors with frames that have no strike prep and for temporarily securing a door that is Exit Only.
-
THE DOOR GAP GAUGE
-
-
The ONLY Gauge you will need to check Fire Door Assembly clearance requirements set forth by NFPA 80 !
-
TRAINING BLOCKS
-
-
USE THESE TRAINING BLOCKS TO LEARN HOW TO INSTALL YOUR LOCKS ! GREAT TRAINING TOOL FOR YOU OR YOUR EMPLOYEES. INVEST IN LEARNING TO DO IT RIGHT OR SPEND MONEY CORRECTING MISTAKES !
-
TRIPLE Pak PLUS COMBO !!
-
-
This should get you started . Save BIG with this Combo !!You get (1) Original Door Dolly (OD-1), (1) Original Door Stand , (1) DOOR BAR , (1) PANIC STRAPP and #1,#2 & #3 Phillips Insert Bit Combo Kit with Stainless Steel Tip holders. !! An...
-
PANIC STRAPP
-
-
Securely holds and balances a panic device while you install !! Takes the place of an ENTIRE PERSON ! WOW !!
-
Burtha's Butt Wax 8 oz
-
-
For smoother drillin', tappin' and screwin' !!
-
READY-SHIMS FOR NON-RATED DOORS
-
-
STOP using trash to shim doors and finish the job like a PRO instead. READY SHIMS are REMOVABLE, RESTICKABLE and STACKABLE.Place them behind the hinge to push door towards the strike or to pull away from strike.You'll Shim doors in less than a...